Vehicle settings and the content displayed on the screen can be changed by using the meter control switches.
â– Setting procedure
1. Press and hold to display
the cursor on the content display
area (center).
2. Press or
with the cursor
on the content display
area (center) to select
and then press .
3. Press or
of the meter
control switches and move
the cursor to select the item
for changing settings.
If the function is turned on and off
or the volume, etc. is changed on
the setting screen, the setting is
changed each time is pressed .
For functions that allow operation
contents, display contents, etc., of
function to be selected, the setting
screen is displayed by pressing and
holding . When the setting
screen is displayed, select the setting
or desired value (time, etc.)
with .
4. After changing the settings,
press of the meter control
switches.
â– LTA (Lane Tracing
Assist)
Select to set up the following items.
Select to enable/disable the lane centering function.
Select to set the lane departure alert sensitivity.
Select to enable/disable the vehicle sway warning.
Select to set the vehicle sway warning sensitivity.
â– BSM (Blind Spot Monitor)
(if equipped)
Select to set up the following items.
â– PCS (Pre-Collision System)
Select to set up the following items.
â– (Intuitive parking
assist) (if equipped)
Select to set up the following items.
â– RCTA (Rear Cross Traffic
Alert) (if equipped)
Select to set up the following items.
â– PKSB (Parking Support
Brake System) (if
equipped)
Select to enable/disable the Parking Support Brake function.
â– RSA (Road Sign Assist)
(if equipped)
Select to set up the following items.
â– Vehicle Settings
Select to set up the following items.
*: Vehicles with Hands Free Power Back Door
Select to set the length of time the Stop & Start system will operate when the "A/C" switch of the air conditioning system is on.
- "Set Pressure"
Select to initialize the tire pressure warning system.- "Change Wheel"
Select to change the tire pressure warning system sensor ID code set. To enable this function, a second set of tire pressure warning system sensor ID codes must be registered by a Toyota dealer.For information regarding changing the registered ID code set, contact your Toyota dealer.
â– Settings
Select to activate/deactivate the Eco Driving Indicator Light.
â– Suspension of the settings display
WARNING
â– Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure that the vehicle is parked in a place with adequate ventilation.
In a closed area such as a garage, exhaust gases including harmful carbon monoxide (CO) may collect and enter the vehicle.
This may lead to death or a serious health hazard.
NOTICE
â– During setting up the display
To prevent battery discharge, ensure that the engine is running while setting up the display features.
Warning message display
Select to display warning messages and measures to be taken if a malfunction is detected.
Convenience Services (Suggestion function)
Displays suggestions to the driver in the following situations.
To select a response to a displayed suggestion, use the meter control switches.
â– Suggestion to turn off the headlights
If the headlights are left on for a certain amount of time after the engine switch has been turned off, a suggestion message will be displayed.
When the headlight switch is in the AUTO position: The message asking if you wish to turn the headlights off is displayed.
To turn the headlights off, select "Yes".
If the driver's door is opened after the engine switch is turned off, this suggestion message will not be displayed.
â– Customization
Convenience Services (Suggestion function) can be turned on/off.
Fail-safe chart
Fail-safe function
When communication fails in any of the main wires
(communication lines) due to a short circuit or other
causes, the fail-safe function, which is specified for
each system, operates to prevent the system from
malfunctioning.
The table below shows the effects on e ...
Changing the display
The multi-information display is
operated using the meter control
switches.
Scroll the screen*/switch the
display*/move the cursor
Press: Enter/Set
Press and hold: Reset/Display
customizable items
Return to the previous screen
Call sending/receiving and
history display (if equipped)
Linke ...
Weight limits
The gross trailer weight must never exceed 1500 lb. (680 Kg).
The gross combination weight must never exceed the gcwr
described below.
2Wd models: 5985 lb. (2715 Kg)
awd models: 6100 lb. (2765 Kg)
The gross vehicle weight must
never exceed the gvwr indicated
on the certification l ...